I needed a monitor hood for quite some time but wasn’t willing to pay the retail prices charged for them, so I decided to build one myself. In this tutorial I’ll show you how to build your own DIY monitor hood for less than $12.

I searched a bit on the Web and found a few tutorials on how to build one. I was inspired by several of them and started building one myself. The material prices are German prices so it may vary in your location, but the costs should be about the same — I spent less than €12 myself.

Note: I am not the most skilled craftsman, so you’ll notice scratches on my hood… but it works!

What You’ll Need

  • Hard foam board. Measure the size of your screen first so you know which size to buy. I got 100 x 50 cm.
  • A box cutter
  • A framing square (the tool with the wooden handle in the pic above)
  • A scale
  • Some fabric tape
  • Some Velcro tape
  • Something to protect your floor while cutting the foam board
  • Patience and a calm hand

The thickness of my foam board is about half a centimeter:

Step 1: Measure and go shopping

First measure the width and height of your monitor, go to the hardware store or order the components from Amazon. (Links on top).

Step 2: Draw your measurements on the foam board

The size of your monitor surely varies, but to give you an idea:

The width of my monitor (top part) was 56cm. The height of the sides of my monitor was 36cm. For all parts, top and sides, I chose to go 20cm deep.

So in my case you end up with 3 parts:

  • 1x 56cm x 20cm
  • 2x 36cm x 20cm

20cm is a good depth and seems to be about the same depth of the DIY monitor hoods you can buy pre-built.

Step 3: Cutting out the parts

Take out your framing square and your box cutter and cut out the pieces you were just drawing. Use the framing square to make sure you cut in a straight line! You don’t need to put too much pressure, the foam board cuts easy.

Make sure you put something underneath the foam board to avoid scratching your floor!

Step 4: Results

If all went well, you should end up with something like this.

Step 5: Modifying the side panels

Now we need to measure the angle of our side panels and cut it out. I went for:

  • 5cm from the top
  • 8cm from the bottom

And you end up with this:

Now take this side panel as a template to cut out your other side panel. The result should look something like this:

Step 6: Cutting out a hole for your calibration device

Of course, if you put the effort in making a DIY monitor hood, you are probably also calibrating your screen with a monitor calibration device. I recommend using DisplayCAL to calibrate your screen and not the Spyder software, a tutorial on how to do this is here. Just use a standard sized CD case to take measurements.

Use a CD case to measure the size of the hole.

Now cut that out. Use your angle tool again to make it straight. I messed this part up a little and didn’t cut exactly straight.

Now take that cut out piece and place it somewhere on the rest of the foam board that you got left (NOT ON YOUR CUT OUT PANELS!) and make sure you got a 2cm border around it.

Now you want to glue the small part in the center of the big part you just cut out. This will make a nice cover for the hole of our calibration device.

Perfect! Well done, we are getting closer to the end.

Step 7: Taping our DIY Monitor Hood together

Now it’s time to get that fabric tape out and tape our side panels to our top panel. Add a strip of tape to the bottom side of your top panel.

Now add a strip of tape to the top side of your top panel, so the side that is facing away from your screen.

Place your side panel to fit exactly together with your top panel and fix the tape. Hold the panel to ensure it’s not falling down before you fix the tape on the inside.

Make sure you really press that sucker tight on the panel, if done right, it should be holding pretty well and be able to stand by itself.

Now repeat that process on the other side. If you done everything right, you end up with something like this:

Step 8: Add Velcro tape

Now it’s time to cut and add velcro tape to both, our DIY Monitor Hood and our monitor.

In the pictures I just added 5 pieces overall, but after I finished everything I found that adding 2 more small pieces on the sides between the top and bottom helped to give a little more cover from the light and make it look a little tighter on the monitor, but try as in pictures first and in case add another piece of velcro.

First stick your velcro tape together if it not already is, to make cutting pieces easier.

Now cut out 5 pieces.

  • 4x 2cm long
  • 1x 6cm long
Place the thinner velcro parts on your screen

Place the longest velcro right on the center top of your screen. Place 2 short pieces on the corners of the top. Place 2 short pieces at the bottom of your monitor’s side.

Add the counterparts on your monitor hood

Now add the counterparts at the exact same locations on your DIY monitor hood. I was just holding it against my monitor and then placing the tape on the monitor hood. Fairly easy.

Step 8: Attaching the DIY Monitor Hood to your monitor!

And you are almost done!

Now just attach the DIY monitor hood onto your monitor and make adjustments if necessary (or add more Velcro if it’s not tight enough for you).

Well done guys! You just saved yourself a hole bunch of money and if you are more skilled with crafting things then I am, you probably have a prettier result, too. I’ve worked with this hood for a few days now and it’s amazing. It really makes a difference, especially if you use 6500k light bulbs in your work space to process your pictures.

This was a cool project for me, and one that’s really easy to do even for the unskilled.


P.S. If this helped you out, please consider clicking on some affiliate links in the article to support me for providing this guide for free.


About the author: Stefan Rosanitsch, also known as Ceos3c online, is a German IT professional with more than 10 years in the tech industry. You can find more of his work and writing on his website, blog, Instagram, and Twitter. This article was also published here.





Source link

Previous articleSee description for new version of this Guide / Tutorial for Xiaomi Mijia Mi Sphere 3.5K camera
Next articleSony Releases World’s First Super Slow Motion Film Shot on a Smartphone